CO2 Incubator 260 Ltr (RT+5~60) Six-Sides Heating Infitek USA
Descriptions
The incubator is ideal for the experiments of the cultivation of
animal cells, sperm/ovum, anaerobic cells, all sorts of microbe cells,
hatching/germinating and special tissues.
Features
- 6 sides direct heating system
Electric heating wire is covered on all sides of the chamber
which makes stable uniformity and provides fast heat-up & temperature
recovery. 3 parts of heating section are controlled and calibrated individually
by 3 temperature sensors.
Warm air from heating wire is preserved in space between the
chamber and the insulation layer. It helps temperature recover faster and
minimize heat loss. Dry wall withinsulation requires no regular maintenance.
Fast & precise detection for CO2 gas
regardless of temperature and humidity.
- Natural humidification using water tray
The heater on bottom side warms the water in tray and it makes
humidification. The circulation fan delivers the moisture formed from the water
in the entire chamber.
Advantages
- Alarm
system: Buzzer to alarm low or high deviation of CO2, temperature.
- Gentle
air and moisture convection: Natural air and moisture convection, air and
moisture in chamber are distributed gentlely by 6-side heating and air
circulation fan.
- Easy
to clean: Rounded corner allows easy cleaning. The entire chamber is made
of stainless steel (SUS304).
- Overheating
limit: Heating is automatically cut by safety device when temperature
control fails or there is excessive heating over set point.
- Perforated
shelves: Perforated shelves are good for natural air flows and are made of
stainless steel which is resistant to rust and contamination.
- No
condensation: Heating by front door heater & frame heater prevents
condensation in the chamber and on the glass door.
- Microprocessor
PID control: Intelligence control for CO2 density, temperature, alarm,
automatic decontamination (Optional).
- HEPA
filtration of the chamber
- Access
port: 25mm Access Port is available at left side. (Upon ordering and
additional charge)
- UV
sterilization: 4W UV is placed on the chamber ceiling and beside the
circulation fan. The UV light cannot reach sample and sterilization is
operated during culturing.
- Maximum
125℃ dry hot air sterilization. No need to remove IR CO2 sensor.
- Monitoring
system: Analog connection port has been designed to observe the status of
equipment in real time even in the far distance.
- Lower
gas consumption. Lower heat loss. Faster recovery easy classification for
various samples.
Optional：
Pressure Reducing Valve, RS232/RS485 communication interface, UV sterilization,
HEPA Filter, Test hole, independent chamber compartment, spare shelf.
Specification
| Model | ICB-CO2-260 |
| Capacity(L) | 260 |
| Circulation Mode | Forced convection |
| Sterilization Mode | 120℃ dry heat sterilization |
| Dimension(W*D*H) | Internal (mm) | 530*590*900 |
| External (mm) | 630*680*1125 |
| Temperature | Range (℃) | RT+5~60 |
| Fluctuation (℃) | ±0.1(37℃) |
| Resolution (℃) | 0.1 |
| Uniformity (℃) | ±0.4 (37℃ / RT.20℃ ) |
| Sensor | PT100 |
| Humidity | Method | Natural vaporization |
| CO2 | Range | 0~20% |
| Uniformity | ±0.1% |
| Resolution | 0.10% |
| Sensor | IR |
| Controller | PID microcomputer |
| Display | LED |
| Material | Internal | 304 stainless steel |
| External | Plastic sprayed stainless steel |
| Shelves(Standard / Max ) | 3/ 8 |
| Test Hole (Optional) | Φ 30mm |
| Safety Device | CO2, temperature deviation buzzer alarm |
| Electricity | Voltage/Frequency | AC 220/110V, 50/60Hz |
| Consumption (W) | 610 |
| N.W./G.W. (kg) | 115/ 140 |
| Shipping Dimension (W*D*H) (mm) | 830*880*1325 |
| Optional | Pressure Reducing Valve， RS232/RS485 communication interface, UV sterilization , HEPA Filter、Test hole, independent chamber compartment，spare shelf |
